webLoaded = "false" Loadclientside=No

Common Stress Types in Adhesive Joints

Regardless of the joint type used, it’s important to understand the different stresses that are imparted onto a bonded assembly. Adhesives and tapes perform at their best when the stress is two-dimensional to the adhesive, dispersing a load across the entire area of a bond line. Adhesives and tapes perform at their worst when the stress is one-dimensional to the adhesive, concentrating a load onto the leading edge of a bond line. Many traditional joint designs incorporate these one dimensional stresses and may require modification for an adhesive bond to be most effective.

webLoaded = "false"
  • Learn about the impact of tensile stress on a bonded assembly.

    Tensile Stress

    Tensile is pull exerted equally over the entire joint. Pull direction is straight, in-plane, and away from the adhesive bond. Force is distributed across the entire area of the bond line.


webLoaded = "false"
  • Learn about the impact of shear stress on a bonded assembly.

    Shear Stress

    Shear is pull directed across the adhesive, forcing the substrates to slide over one another. Here again, the force is in-plane, and the force is distributed across the entire area of the bond line.


webLoaded = "false"
  • Learn about the impact of compression stress on a bonded assembly.

    Compression Stress

    Like tension, compression is a force applied to a bond that is in-plane and straight. Unlike tension, the force is being applied toward the adhesive. Force is distributed across the entire area of the bond line.


webLoaded = "false"
  • Learn about the impact of cleavage stress on a bonded assembly.

    Cleavage Stress

    Cleavage is pull concentrated at one edge of the joint, exerting a prying force on the bond. While one end of the adhesive joint is experiencing concentrated stress on the leading edge, the other edge of the joint is theoretically under zero stress. Cleavage occurs with two rigid substrates.


webLoaded = "false"
  • Learn about the impact of peel stress on a bonded assembly.

    Peel Stress

    Peel is a pull that is also concentrated at one edge of the joint. One of the substrates is flexible, resulting in even more concentration at the leading edge than with a cleavage joint.


webLoaded = "false" Loadclientside=No

Designing Adhesive Joints

Joints that are well designed for adhesives place a majority of the stress into tensile, compression or shear modes. This allows the force to be applied over the entire adhesive area. Joints placing stress into cleavage or peel concentrate the stress onto the leading edge which may lead to premature bond failures, especially if subjected to vibration, impact or fatigue.

In addition to the stress type, optimizing a joint may also require consideration of the dimensions. Adhesives are tested and reported for their approximate performance in units of force per area (e.g. shear loading, Newtons per square meter) or force per length (e.g. peel, Newtons per centimeter). By configuring the bond dimensions to accommodate loads imparted per area, bond durability can be improved.


webLoaded = "false"

Related education articles


Connect With Us
We're here to help.

Need help finding the right product for your project? Contact us if you need product, technical or application advice or want to collaborate with a 3M technical specialist, or give us a call at 1-800-831-0658.

Need help finding the right product for your project? Contact us if you need product, technical or application advice or want to collaborate with a 3M technical specialist, or give us a call at 1-800-831-0658.

Close  

Industrial Adhesives & Tapes | Ask A 3M Expert



Thank you for your interest! Please complete the form below to receive your tape or adhesives sample or enter your question or comment below.


Industrial Users Only


Disclaimer: The 3M Industrial Sample Request Program is not available to consumers or the general public. We reserve the right to disqualify without notification any sample request that does not appear to be for industrial manufacturing purposes. Samples are available to U.S. industrial customers only. Only one sample per qualified customer. You will be contacted to verify your request. If you are a 3M Distributor, contact your 3M Sales Representative. Quantities available while supplies last.


We will respond to your email request in 24 - 48 business hours.


All fields are required unless indicated optional


  •  
  • 3M takes your privacy seriously. 3M and its authorized third parties will use the information you provided in accordance with our Privacy Policy to send you communications which may include promotions, product information and service offers. Please be aware that this information may be stored on a server located in the U.S. If you do not consent to this use of your personal information, please do not use this system.

  • Submit

Thank You

Thank you for your interest in 3M Industrial Adhesives & Tapes products. A 3M representative will contact you shortly regarding your inquiry.

Our Apologies...

An error has occurred while submitting. Please try again later...

CHAT WITH US
Follow Us
Change Location
United States - English