3M™ 15kV 1/C PILC Splicing Kit QS2011T, 5 - 35 kV, Poly/EPR Paper Insulated Lead Covered (PILC), 1/case
- Part Number QS2011T
- 3M ID 7100034389
- UPC 00054007505464
Details
Highlights
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- Maintains resiliency and pressure even after years of aging and exposure
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or single conductor PILC cable to single conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. Each kit makes one single conductor splice. Use 3M™ Scotchlok™ Connectors 2000T Series with these splice kits. Each kit contains sufficient quantities of material to make one splice. Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
Typical properties
Resources
Similar products
| Voltage | 5 kV, 8 kV, 15 kV, 35 kV, 25/28 kV | |||
| Number of Conductors | 1 | |||
| Cable Shielding | PILC | |||
| Splice Type | PILC Transition | |||
| Insulation Outer Diameter (Metric) | 14.224 mm, 14.478 mm, 14.732 mm, 14.986 mm, 15.24 mm, 15.494 mm, 15.748 mm, 16.002 mm, 16.256 mm, 16.51 mm, 16.764 mm, 17.018 mm, 17.272 mm, 17.526 mm, 17.78 mm, 18.034 mm, 18.288 mm, 18.542 mm, 18.796 mm, 19.05 mm, 19.304 mm, 19.558 mm, 19.812 mm, 20.066 mm, 20.32 mm, 20.574 mm, 20.828 mm, 21.082 mm, 21.336 mm, 21.59 mm, 21.844 mm, 22.098 mm, 22.352 mm | |||
| Insulation Outer Diameter (Imperial) | 0.56 in, 0.57 in, 0.58 in, 0.59 in, 0.6 in, 0.61 in, 0.62 in, 0.63 in, 0.64 in, 0.65 in, 0.66 in, 0.67 in, 0.68 in, 0.69 in, 0.7 in, 0.71 in, 0.72 in, 0.73 in, 0.74 in, 0.75 in, 0.76 in, 0.77 in, 0.78 in, 0.79 in, 0.8 in, 0.81 in, 0.82 in, 0.83 in, 0.84 in, 0.85 in, 0.86 in, 0.87 in, 0.88 in |
3M™ 15kV 1/C PILC Splicing Kit QS2011T, 5 - 35 kV, Poly/EPR Paper Insulated Lead Covered (PILC), 1/case
3M™ Cold Shrink Shielded Splice Kits 5550 Series
3M™ Cold Shrink Quick Splice Kits QSLV-M Series
3M™ Cold Shrink Inline Splice Kits 5730 SeriesFor industrial/occupational use only. Not for consumer sale or use.
3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.
