3M™ Cold Shrink Splice Kit QS2013T, CN, JCN, PILC, 15 kV, 400-1000 kcmil PILC, 500-1000 kcmil Poly/EPR, 1/case
- Part Number QS2013T
- 3M ID 7100021287
- UPC 00054007505556
Details
Highlights
- Oil stop tubes provide rejacketing and moisture-seal protection to the splice
- Resists water and eliminate the need of sweat lead
- Designed for PILC transition to the poly/EPR cable
- Rated for 15 kV applications
- Maintains resiliency and pressure even after years of aging and exposure
The 3M™ Cold Shrink Splice Kit QS-2000T Series allows you to splice either single-conductor PILC cable to single-conductor PILC cable, or singleconductor PILC cable to single-conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. The 3M™ Cold Shrink Splice Kit QS-2000T Series meets the requirements of IEEE 404.
This kit allows you to splice either single conductor PILC cable to single conductor PILC cable, or single conductor PILC cable to single conductor Poly/EPR cable. Because of the design of the splice, size transitions can also be accommodated rather easily. Each kit makes one single conductor splice. Use 3M™ Scotchlok™ Connectors 2000T Series with these splice kits. Each kit contains sufficient quantities of material to make one splice. Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.
Typical properties
Resources
Similar products
| Voltage | 15 kV | |||
| Number of Conductors | 1 | |||
| Cable Shielding | PILC | |||
| Splice Type | PILC Transition | |||
| Insulation Outer Diameter (Metric) | 24.892 mm, 25.146 mm, 25.4 mm, 25.654 mm, 25.908 mm, 26.162 mm, 26.416 mm, 26.67 mm, 26.924 mm, 27.178 mm, 27.432 mm, 27.686 mm, 27.94 mm, 28.194 mm, 28.448 mm, 28.702 mm, 28.956 mm, 29.21 mm, 29.464 mm, 29.718 mm, 29.972 mm, 30.226 mm, 30.48 mm, 30.734 mm, 30.988 mm, 31.242 mm, 31.496 mm, 31.75 mm, 32.004 mm, 32.258 mm, 32.512 mm, 32.766 mm, 33.02 mm, 33.274 mm, 33.528 mm, 33.782 mm, 34.036 mm, 34.29 mm, 34.544 mm, 34.798 mm, 35.052 mm, 35.306 mm, 35.56 mm, 35.814 mm, 36.068 mm, 36.322 mm, 36.576 mm, 36.83 mm, 37.084 mm, 37.338 mm, 37.592 mm, 37.846 mm, 38.1 mm, 38.354 mm, 38.608 mm, 38.862 mm, 39.116 mm, 39.37 mm, 39.624 mm | |||
| Insulation Outer Diameter (Imperial) | 0.98 in, 0.99 in, 1 in, 1.01 in, 1.02 in, 1.03 in, 1.04 in, 1.05 in, 1.06 in, 1.07 in, 1.08 in, 1.09 in, 1.1 in, 1.11 in, 1.12 in, 1.13 in, 1.14 in, 1.15 in, 1.16 in, 1.17 in, 1.18 in, 1.19 in, 1.2 in, 1.21 in, 1.22 in, 1.23 in, 1.24 in, 1.25 in, 1.26 in, 1.27 in, 1.28 in, 1.29 in, 1.3 in, 1.31 in, 1.32 in, 1.33 in, 1.34 in, 1.35 in, 1.36 in, 1.37 in, 1.38 in, 1.39 in, 1.4 in, 1.41 in, 1.42 in, 1.43 in, 1.44 in, 1.45 in, 1.46 in, 1.47 in, 1.48 in, 1.49 in, 1.5 in, 1.51 in, 1.52 in, 1.53 in, 1.54 in, 1.55 in, 1.56 in |
3M™ Cold Shrink Splice Kit QS2013T, CN, JCN, PILC, 15 kV, 400-1000 kcmil PILC, 500-1000 kcmil Poly/EPR, 1/case
3M™ Cold Shrink Shielded Splice Kits 5550 Series
3M™ Cold Shrink Quick Splice Kits QSLV-M Series
3M™ Cold Shrink Inline Splice Kits 5730 SeriesFor industrial/occupational use only. Not for consumer sale or use.
3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.
