Item 1 of 1

3M™ Industrial Loadbreak Elbows 5810 Series

1 of 0

Hover to zoom

Ideal for connecting underground cable to transformers, switchgear and junctions that come with loadbreak bushings
Cold shrink tube seals from the bottom of the elbow to the cable jacket
Specially designed for use on tape shield, wire shield, UniShield® and jacketed concentric neutral types of cables
High-quality, peroxide-cured EPDM provides better insulation

View all details

For industrial/occupational use only. Not for consumer sale or use.

Specifications

Attribute Name	Value
Brand	3M™
Cable Type	Compact/Solid, Stranded
Cable Voltage Rating	15 kV, 5 kV, 8 kV
Component Type	Elbow
Conductor Sizes (Imperial)	1 AWG, 1/0 AWG, 2 AWG, 2/0 AWG, 250 kcmil, 3/0 AWG, 4/0 AWG
Current Rating	200 A
Family	3M™ 200 Amp 5-15 kV Industrial Loadbreak Elbow
Includes Compression Connector	Yes
Insulation Diameter Range	0.495-0.585 in, 0.575-0.685 in, 0.630-0.820 in, 0.700-0.910 in, 0.850-1.100 in
Insulation Diameter Range (Metric)	12.6-14.9 mm, 14.6-17.4 mm, 16.0-20.8 mm, 17.8-23.1 mm, 21.6-27.9 mm
Insulation Level	100%, 133%
Insulation Outside Diameter Range	0.495 to 0.585 in, 0.575 to 0.685 in, 0.63 to 0.82 in, 0.7 to 0.91 in, 0.85 to 1.1 in
Maximum Insulation Outer Diameter (Imperial)	0.585 in, 0.685 in, 0.82 in, 0.91 in, 1.1 in
Maximum Insulation Outer Diameter (Metric)	15 mm, 17 mm, 21 mm, 23 mm, 28 mm
Maximum Operating Voltage	15 kV, 5 kV, 8 kV
PlantAnalystID	ABBA-Z1GUQ
Product Series	5810
Product Type	Accessory
RoHS 2011/65/EU Compliant	Undetermined
RoHS EU Comments	Contact 3M for information
Separable Connector Type	Load Break Elbows
Units per Case	1

Details

Ideal for connecting underground cable to transformers, switchgear and junctions that come with loadbreak bushings
Cold shrink tube seals from the bottom of the elbow to the cable jacket
Specially designed for use on tape shield, wire shield, UniShield® and jacketed concentric neutral types of cables
High-quality, peroxide-cured EPDM provides better insulation
Meets ANSI/IEEE Standard 386.

3M™ 5810 Series Industrial Loadbreak Elbow Kit is a fully shielded and insulated dead front termination. This kit is for connecting underground cable to transformers, switchgear and junctions that come with loadbreak bushings. It is designed for use on tape shield, wire shield, UniShield® and JCN types of cables. The elbow is peroxide cured EPDM.

3M™ 5810 Series Industrial Loadbreak Elbow Kit includes an elbow body, loadbreak probe, probe installation tool, silicone lubricant, cold shrink jacketing tube, mastic strips, ground braid assembly, constant force spring and CC 3 cable cleaning pads. This kit is rated for 5 to 15 kV, 200 amp applications. Meets ANSI/IEEE Standard 386.

Resources

Catalogs

3M™ Separable Connectors, 2013 Electrical Products Catalog (PDF, 1.9MB)

Data Sheets

5810 Series Industrial Loadbreak Elbow (PDF, 489.5KB)

Instructions

Regulatory Material

EMD Shelf Life Statement (PDF, 90.3KB)

Safety Data Sheets

5810 Series 200 Amp Industrial Loadbreak Elbows (w/C-Si Grease) (PDF)

For industrial/occupational use only. Not for consumer sale or use.

3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.