3M™ Cold Shrink QT-II Outdoor Termination Kits 7645-T-HSG-L-110, Indoor
- Part Number 7645-T-HSG-L-110
- 3M Product Number 7645-T-HSG-L-110
- 3M ID 7100165409
- UPC 00051128602874
Details
Highlights
- Provides a void-free seal to tape shield, wire-over-tape shield and longitudinally corrugated shield power cables
- High dielectric-constant material regulates the distribution of electric field stress
- Suitable for indoor and high-ampacity ground applications
- Molded, silicone rubber insulation offers durability and provides constant radial pressure
3M™ Cold Shrink QT III 7640 T HSG & 7650 T HSG Series Termination Kit includes a non skirted, 1 piece termination. It ensures a pliable, tight seal for tape shield and longitudinally corrugated shield power cables. The conjunction of high dielectric constant material and sealing compounds allows the termination to withstand voltages of 5 to 35kV.
Each kit contains sufficient quantities of material to make one single-phase termination for high fault current cables. The termination assemblies consist of a tubular insulator, high dielectric constant (Hi-K) stress control tube, conformable Hi-K stress controlling compound, and built-in environmental top seal. The insulator is made of a dark gray silicone rubber with advanced tracking resistant and hydrophobic properties. Note: Lugs need to be ordered separately. Exceptions: For T-150 Kits, 150 kV impulse level meets the impulse requirements for 35 kV class equipment where indoor terminations are used.
Typical properties
Resources
Similar products
| Voltage | 5 kV, 8 kV, 15 kV | ||
| Conductor Sizes (Imperial) | 750 kcmil, 1000 kcmil | ||
| Number of Conductors | 1 | ||
| Breakout Boot | No | ||
| Insulation Outer Diameter (Imperial) | 1.15 in, 1.16 in, 1.17 in, 1.18 in, 1.19 in, 1.2 in, 1.21 in, 1.22 in, 1.23 in, 1.24 in, 1.25 in, 1.26 in, 1.27 in, 1.28 in, 1.29 in, 1.3 in, 1.31 in, 1.32 in, 1.33 in, 1.34 in, 1.35 in, 1.36 in, 1.37 in, 1.38 in, 1.39 in, 1.4 in, 1.41 in, 1.42 in, 1.43 in, 1.44 in, 1.45 in, 1.46 in, 1.47 in, 1.48 in, 1.49 in, 1.5 in, 1.51 in, 1.52 in, 1.53 in, 1.54 in, 1.55 in, 1.56 in, 1.57 in, 1.58 in, 1.59 in, 1.6 in, 1.61 in, 1.62 in, 1.63 in, 1.64 in, 1.65 in, 1.66 in, 1.67 in, 1.68 in, 1.69 in, 1.7 in, 1.71 in, 1.72 in, 1.73 in, 1.74 in, 1.75 in, 1.76 in, 1.77 in, 1.78 in, 1.79 in, 1.8 in, 1.81 in, 1.82 in, 1.83 in, 1.84 in, 1.85 in, 1.86 in, 1.87 in, 1.88 in, 1.89 in, 1.9 in, 1.91 in, 1.92 in, 1.93 in, 1.94 in, 1.95 in, 1.96 in, 1.97 in, 1.98 in |
3M™ Cold Shrink QT-II Outdoor Termination Kits 7645-T-HSG-L-110, Indoor
3M™ Cold Shrink QT-III Termination Kit 7640-T & 7650-T Series for 5-35 kV
3M™ Cold Shrink QT-III Termination Kit 7600-T-3-RJS Series for 5-35 kVFor industrial/occupational use only. Not for consumer sale or use.
3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.
