The Standard Abrasives™ Aluminum Oxide Buff and Blend Roll combines nylon strands and aluminum oxide with a resin bond, resulting in an open web that is responsive and durable enough for deburring, cleaning, blending and finishing. Available in a versatile range of grades and sizes, you can choose the right roll for your application.
The trick to our Standard Abrasives™ Aluminum Oxide Buff and Blend Roll is uncovering the right Buff & Blend material for your project. Various Buff & Blend materials were created so rolls could be used for different applications, and the materials help distinguish one roll from another.
Choosing the Right Buff & Blend Material
Each of the Standard Abrasives Buff & Blend materials offers unique benefits. Standard Abrasives Buff & Blend materials include: GP, AP, HS and HS-F.
GP is a general purpose material that delivers a high cut rate and consistent finish. It is the most middle-of-the-road, multi-purpose material among all the standard abrasives buff & blend materials. It's great for general-duty applications, like intermediate cleaning, blending, deburring and finishing - striking a balance between aggressive cutting action and fine finishing. AP material is a cut above GP in terms of its aggressiveness, and it will produce a coarser finish than GP material.
HS and HS-F material are both high strength. The material is very tear resistant, so it's a good match for final finishing on irregularly-shaped parts, because it will not break down or fray when it comes in contact with contours and extrusions. HS-F material is the best material for light deburring and finishing, because the fineness of the mineral produces a consistent, soft scratch pattern when sanding brass, steel, bronze and stainless steel surfaces.
Standard Abrasives™ Aluminum Oxide Buff and Blend Rolls come in varying widths, from 1 inch to 38 inches. We purposefully designed these roles in different sizes, so they would fit with a range of sanding tools. Whether the workpiece is large or small, it's likely one of these widths will be a good match for the size of the workpiece. These materials may be used on orbital or straight-line sanders to produce matte and satin finishes or may be cut and shaped for hand-sanding applications.
|1||2||3||4||5||Buff & Blend Material|
|GP||HP||HS Reg||HS Coarse|
|Blend: Blend minor surface imperfections, handling marks, coated abrasives secondary burrs||1 (GP VFINE)||3
|4 (GP MED)|
|Clean: Remove minor surface oxidation, coatings and rust; surface preparation prior to coating||1
|Deburr: Remove part lines from small castings, small burrs from threaded pipes, flash from plastic molded parts||1
|Finish: Grain finishing on Stainless Steel after weld removal, cosmetic finishing on Aluminum castings||1 (HS VFINE)||5
|4 (HS MED)|
|Center hole discs may be ganged on a shaft and used as a wheel||•||•||•||•|
|Resists loading: No metal contamination to work piece||•||•||•||•|
|Extended duration of cut||•|
|Eliminated edge fraying and grain shredding||•||•||•|
|Reduced cost resulting from product durability and increased productivity||•||•||•|
|High Nickel/Chrome Alloys||•||•||•||•|
|Very Fine A/O||Maroon||Red||Pink|
|Very Fine S/C||Gray|
3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use. Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice. Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage. For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.