1. United States
  2. All 3M Products
  3. Electrical
  4. Splices & Accessories
  5. Cold Shrink Splices
  6. 3M™ Cold Shrink Quick Splice Low Voltage QSLV-M 8-2/0, Non-shielded, 1 kV, 10/case

3M™ Cold Shrink Quick Splice Low Voltage QSLV-M 8-2/0, Non-shielded, 1 kV, 10/case

  • Part Number QSLV-M(8-2/0)
  • 3M ID 7000058804
  • UPC 00051128572368

Rubber sleeve with sealing mastic provides a water-resistant sealing

Factory-expanded for easy installation

For direct-bury, secondary low-voltage, non-shielded cable splices

View more details
Frequently viewed resources
Tech Data Sheet (PDF, 79KB)Safety Data Sheet (PDF, 0B)
Conductor Sizes (Imperial) 2 AWG
Insulation Outer Diameter (Metric) 11.176 mm, 11.43 mm, 11.684 mm, 11.938 mm, 10.16 mm, 10.414 mm, 10.668 mm, 10.922 mm, 12.446 mm, 12.7 mm, 12.192 mm, 12.954 mm, 13.208 mm, 14.224 mm, 13.462 mm, 13.716 mm, 13.97 mm, 14.478 mm, 14.986 mm, 15.24 mm, 15.494 mm, 15.748 mm, 14.732 mm, 16.002 mm, 16.256 mm, 16.51 mm, 16.764 mm, 17.018 mm, 17.272 mm, 17.526 mm, 17.78 mm, 18.288 mm, 18.034 mm, 18.542 mm, 18.796 mm, 19.05 mm, 6.096 mm, 6.35 mm, 6.604 mm, 6.858 mm, 5.08 mm, 5.334 mm, 5.842 mm, 5.588 mm, 7.112 mm, 7.366 mm, 7.62 mm, 7.874 mm, 9.398 mm, 9.652 mm, 9.906 mm, 8.128 mm, 8.382 mm, 8.636 mm, 8.89 mm, 9.144 mm
Maximum Conductor Size (Imperial) 2/0 AWG
Maximum Conductor Size (Metric) 70 mm²
Minimum Conductor Size (Metric) 10 mm²
Conductor Sizes (Metric) 35 mm²

Details

Highlights
  • Rubber sleeve with sealing mastic provides a water-resistant sealing
  • Factory-expanded for easy installation
  • For direct-bury, secondary low-voltage, non-shielded cable splices
  • Rated for up to 1 kV applications
  • Splices both aluminum and copper conductors
  • RoHS 2011/65/EU Compliant and ANSI Certified

3M™ Cold Shrink Quick Splice Low Voltage QSLV-M are open-ended tubular rubber sleeves with sealing mastic on each end which are factory expanded and assembled onto a unique three-core system. Two cores, one on each end, are removed after the QSLV-M insulator has been centered over an inline connector, allowing the ends of the tube to shrink and form a water-resistant seal. The third, center segment of the core remains inside the cold shrink tube, acting as a support structure. Sizing of the cores and tube, along with the sealing mastic on each end, is designed to accommodate the variance in connectors and connector crimping techniques and final dimensions without degrading the seal and insulating characteristics of the EPDM rubber tube, while also making core removal easy. Two diameter sizes will cover a range of 1 kV or less cable from 8 AWG through 1000 kcmil for copper and 8 AWG through 500 kcmil for aluminum conductors with crimped connectors. In aerial applications where intense UV radiation will be common and visual inspection is not possible, it is recommended to overwrap the tubing with Scotch® Super 33+™ Vinyl Electrical Tape or Scotch® Self-Fusing Silicone Rubber Electrical Tape 70. Note: Insulator may be used on cable sizes outside of the recommended range provided both cables are within the insulation O.D. range, and the connector meets the dimensional requirements shown in the table.

Typical properties

Resources

Manufacturing Origin: USA

The designation that a product is Manufactured in the USA means the product undergoes substantial transformation in one of our U.S. Manufacturing plants. Some products contain imported components.

Note: 3M products offered on a government contract that require country of origin representation must be certified by 3M Trade Compliance. Contact customer service at 800-245-3573 to request a certificate.
For industrial/occupational use only. Not for consumer sale or use.

3M industrial and occupational products are intended, labeled, and packaged for sale to trained industrial and occupational customers for workplace use.  Unless specifically stated otherwise on the applicable product packaging or literature, these products are not intended, labeled, or packaged for sale to or use by consumers (e.g., for home, personal, primary or secondary school, recreational/sporting, or other uses not described in the applicable product packaging or literature), and must be selected and used in compliance with applicable health and safety regulations and standards (e.g., U.S. OSHA, ANSI), as well as all product literature, user instructions, warnings, and other limitations, and the user must take any action required under any recall, field action, or other product use notice.  Misuse of 3M industrial and occupational products may result in injury, sickness, death, or property damage.  For help with product selection and use, consult your on-site safety professional, industrial hygienist, or other subject matter expert.