1. All 3M Products

Dynatron™ Dyna-Hair Long Strand

Products
  • Fills splits, cracks or holes in fiberglass or metal
  • Improved strength and flexibility to prevent cracking
  • Waterproof, for protected use in unpainted areas
  • Creates a smooth, professional-quality repair
 More...
Volume (Imperial)
Volume_Imperial
Volume (Metric)
Volume_Metric
Products Available
Available options:
 Volume (Imperial) and Volume (Metric)
All Options
Close
Specifications
Attribute Name
Value
Application
Dent Fill, Rust Out Repair
Brand
3M™
Case Quantity
12 Cans per Case, 4 Cans per Case
Consistency
Paste
Consumer Label
Yes
Container Size (Imperial)
1 Gallon, 1 Quart
Container Type
Can
Dry Time
20 Minutes
Handling Time
3-5 Minutes
Number per Inner
1 per Can
Performance Level
Good
Product Color
Green
Product Type
Glass Reinforced Filler
Sandability
Good
Volume (Imperial)
1 gal, 32 fl oz
Volume (Metric)
0.95 L, 3.78 L
Work Time
4 Minutes
Details
  • Fills splits, cracks or holes in fiberglass or metal
  • Improved strength and flexibility to prevent cracking
  • Waterproof, for protected use in unpainted areas
  • Creates a smooth, professional-quality repair
  • Compatible with most automotive paints

Our Dynatron™ Dyna-Hair® Long Strand body filler repairs splits, cracks and holes in all kinds of surfaces, including wood, fiberglass, aluminum and bare or galvanized steel. Reinforced with long fiberglass strands, this waterproof filler offers additional versatility to any automotive repair.

 

Dynatron™ Dyna-Hair™ reinforced body filler provides a balance of performance and economy when repairing splits, cracks or rust holes in automotive bodies.
Waterproof repairs twice the strength of ordinary body fillers

Balance of Performance
Dynatron™ Dyna-Hair™ reinforced body filler provides a balance of performance and economy when repairing splits, cracks or rust holes in automotive bodies. Reinforced with long-strand fiberglass, this filler creates waterproof repairs that are twice the strength of ordinary body fillers. Our two-component polyester compound applies easily and creates a smooth, professional-quality repair. This filler is produced with the highest quality resins, talc and microspheres. Dynalite has become an industry standard because it combines ease of use, faster working properties and top-notch results.

Automotive body technicians rely on our filler for its good adhesion, consistent quality and compatibility with most paints. It combines spreading, easy mixing, good featheredging, and non separating properties into one filler.

Using Dynatron™ Dynalite™ Light Weight Body Filler is as Easy as this Simple 6-step Process:

  1. Clean the repair area using soap and water followed by a wax & grease remover/surface cleaner. Sand the surface as needed with grade P40 to P80 3M™ abrasive.
    Note: If grinding is required use a grade 50 3M™ grinding disc, blow off the sanding dust with clean dry air. If repairing galvanized steel, e-coat, primed/painted surfaces or aluminum, sand with grade P80 3M™ abrasive to remove the paint/primer. Blow off with clean dry compressed air and re-clean the surface using a clean paper or cloth towel and a wax & grease remover/surface cleaner.
  2. Apply the required amount of body filler to a clean mixing surface. (Do not use discarded cardboard as a mixing surface as contamination may occur.) The correct hardener to filler ratio = 3 inch diameter circle 1/2 inch thick of filler to a 3 inch strip of cream hardener.
  3. Mix the body filler and cream hardener thoroughly, to a uniform color. Gel time/setting time is approximately 3-5 minutes @ 75°F (24°C) using 2% hardener as prescribed. Spread the filler on the mixing board, being sure to break any air bubbles that were introduced during mixing.
  4. Apply a thin layer using firm pressure to ensure maximum adhesion being sure to "wet out" the surface completely. Apply additional filler in layers, building up the damaged area higher than the surrounding surface. Maximum filler thickness should not exceed 1/4 inch. Allow curing time of 20 minutes.
  5. Sand the filler to the proper contour with 3M™ abrasives, using the following recommended grade sequence: P40, P80, P180. Note: If more filler is needed blow off with clean dry compressed air and follow steps 2 through 6.
  6. Wait approximately 45 minutes before applying primer and paint, always follow your paint company's recommended procedures.

 

Customer Reviews
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • CLOUD, getContent, 17ms
  • REVIEWS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;
Product Support

Specific product and application questions

SEND US A MESSAGE

Message Us

We welcome your questions and comments about 3M Products and only use the information you provide to respond to your message.

All fields are required unless indicated optional.

  • The information you provide on this Contact Us form will be used to respond to your request and as further described in our  Internet Privacy Policy.

    Please be aware that this information (including the original and the subsequent reply) may be transferred to a server located in the U.S. for metrics and storage. If you do not consent to this use of your personal information, please do not use the Contact Us system.