1. All 3M Products
  • Dynatron™ Dyna-Hair Long Strand
  • Dynatron™ Dyna-Hair Long Strand

    Products
    • Fills splits, cracks or holes in fiberglass or metal
    • Improved strength and flexibility to prevent cracking
    • Waterproof, for protected use in unpainted areas
    • Creates a smooth, professional-quality repair
     More...
    Size
    Products Available
    Available options:
     Size
    All Options
    Close
    Specifications
    Attribute Name
    Value
    Application
    Dent Fill, Rust Out Repair
    Brand
    3M™
    Case Quantity
    12 Cans per Case, 4 Cans per Case
    Color
    Green
    Consistency
    Paste
    Consumer Label
    Yes
    Container Size (Imperial)
    1 Gallon, 1 Quart
    Container Type
    Can
    Dry Time
    20 Minutes
    Handling Time
    3-5 Minutes
    Number per Inner
    1 per Can
    Performance Level
    Good
    Product Type
    Glass Reinforced Filler
    Sandability
    Good
    Size
    1 Gallon, 1 Quart
    Work Time
    4 Minutes
    Details
    • Fills splits, cracks or holes in fiberglass or metal
    • Improved strength and flexibility to prevent cracking
    • Waterproof, for protected use in unpainted areas
    • Creates a smooth, professional-quality repair
    • Compatible with most automotive paints

    Our Dynatron™ Dyna-Hair® Long Strand body filler repairs splits, cracks and holes in all kinds of surfaces, including wood, fiberglass, aluminum and bare or galvanized steel. Reinforced with long fiberglass strands, this waterproof filler offers additional versatility to any automotive repair.

     

    Dynatron™ Dyna-Hair™ reinforced body filler provides a balance of performance and economy when repairing splits, cracks or rust holes in automotive bodies.
    Waterproof repairs twice the strength of ordinary body fillers

    Balance of Performance
    Dynatron™ Dyna-Hair™ reinforced body filler provides a balance of performance and economy when repairing splits, cracks or rust holes in automotive bodies. Reinforced with long-strand fiberglass, this filler creates waterproof repairs that are twice the strength of ordinary body fillers. Our two-component polyester compound applies easily and creates a smooth, professional-quality repair. This filler is produced with the highest quality resins, talc and microspheres. Dynalite has become an industry standard because it combines ease of use, faster working properties and top-notch results.

    Automotive body technicians rely on our filler for its good adhesion, consistent quality and compatibility with most paints. It combines spreading, easy mixing, good featheredging, and non separating properties into one filler.

    Using Dynatron™ Dynalite™ Light Weight Body Filler is as Easy as this Simple 6-step Process:

    1. Clean the repair area using soap and water followed by a wax & grease remover/surface cleaner. Sand the surface as needed with grade P40 to P80 3M™ abrasive.
      Note: If grinding is required use a grade 50 3M™ grinding disc, blow off the sanding dust with clean dry air. If repairing galvanized steel, e-coat, primed/painted surfaces or aluminum, sand with grade P80 3M™ abrasive to remove the paint/primer. Blow off with clean dry compressed air and re-clean the surface using a clean paper or cloth towel and a wax & grease remover/surface cleaner.
    2. Apply the required amount of body filler to a clean mixing surface. (Do not use discarded cardboard as a mixing surface as contamination may occur.) The correct hardener to filler ratio = 3 inch diameter circle 1/2 inch thick of filler to a 3 inch strip of cream hardener.
    3. Mix the body filler and cream hardener thoroughly, to a uniform color. Gel time/setting time is approximately 3-5 minutes @ 75°F (24°C) using 2% hardener as prescribed. Spread the filler on the mixing board, being sure to break any air bubbles that were introduced during mixing.
    4. Apply a thin layer using firm pressure to ensure maximum adhesion being sure to "wet out" the surface completely. Apply additional filler in layers, building up the damaged area higher than the surrounding surface. Maximum filler thickness should not exceed 1/4 inch. Allow curing time of 20 minutes.
    5. Sand the filler to the proper contour with 3M™ abrasives, using the following recommended grade sequence: P40, P80, P180. Note: If more filler is needed blow off with clean dry compressed air and follow steps 2 through 6.
    6. Wait approximately 45 minutes before applying primer and paint, always follow your paint company's recommended procedures.

     

    Customer Reviews
    • bvseo_sdk, java_sdk, bvseo-4.0.0
    • CLOUD, getContent, 64ms
    • REVIEWS, PRODUCT
    • bvseo-msg: The resource to the URL or file is currently unavailable.;
    Product Support

    Specific product and application questions

    SEND US A MESSAGE

    Message Us

    We welcome your questions and comments about 3M Products and only use the information you provide to respond to your message.

    All fields are required unless indicated optional.

    • The information you provide on this Contact Us form will be used to respond to your request and as further described in our  Internet Privacy Policy.

      Please be aware that this information (including the original and the subsequent reply) may be transferred to a server located in the U.S. for metrics and storage. If you do not consent to this use of your personal information, please do not use the Contact Us system.

    Follow Us
    The brands listed above are trademarks of 3M.
    Change Location
    United States - English