1. All 3M Products
  • 3M™ High Bond Rearview Mirror Adhesive
  • 3M™ High Bond Rearview Mirror Adhesive

    Part Number 087493M ID 60455070858UPC 00051135087497
    • Two-part structural acrylic system designed to mount rear view mirrors
    • Holds up well in high temperatures and humid environments
    • Resistant to moisture, chemicals, vibration and impact
    • Simple application procedure

    3M™ High Bond Rear View Mirror Adhesive permanently bonds the rear view mirror bracket to windshields. This two-part structural acrylic adhesive is specially formulated to bond two non-porous materials together. A specialty adhesive is recommended for rear view mirror installation because of the critical nature of the application. Rear view mirrors exist in an environment with challenging conditions that exceed the capacity of many adhesives.

    Here is how our 3M™ High Bond Rear View Mirror Adhesive excels:

    Professional Strength - The adhesive creates a strong bond that resists failure, even in very challenging conditions. Adhesive is resistant to chemicals.

    Heat tolerant - When standing outdoors in direct sunlight, the windshield of a car becomes hot. Our adhesive is made to keep its secure attachment under those punishing conditions.

    Humidity resistant - In regions where humidity is a factor, it's important that the adhesive resists degradation that can come from moisture in the air.

    Moisture resistant - Windshields can become damp with dew and moisture condensation. Our adhesive maintains its integrity when exposed to those environmental factors.

    Vibration resistant - Rear view mirrors take a lot of punishment from the vibrations that occur as vehicles ride over rough roads. Our adhesive is formulated to withstand the bumps and bands that occur a car travels on typical roads.

    Impact resistant - With its position in a car, a rear view mirror can occasionally be bumped. Our super strong adhesive will keep holding under normal circumstances where moderate impacts occur.

    3M™ High Bond Rear View Mirror Adhesive is perfect for installing new mirrors or ones that broke free from the windshield. This product is commonly used by windshield replacement and automotive restoration professionals.

    Our two-part system comes with an adhesive and activator in separate tubes. It cures in approximately 15 minutes.

    • Two-part structural acrylic system designed to mount rear view mirrors
    • Holds up well in high temperatures and humid environments
    • Resistant to moisture, chemicals, vibration and impact
    • Simple application procedure
    • Cures in 15 minutes, depending on environmental conditions
    Attribute Name
    Adhesive Type
    Case Quantity
    12 Bags per Case
    Container Type
    Cure Time
    15-30 Minutes
    Volume (Imperial)
    0.02 fl oz
    Customer Reviews
    3M™ High Bond Rearview Mirror Adhesive is rated 1.0 out of 5 by 3.
    Rated 1 out of 5 by from Don't waste your money After reading the other reviews, I felt that they likely hadn't cleaned and prepared the surface adequately - or did not wait long enough, Pulled vehicle into climate control garage, prepped meticulously followed instructions, gave 5 days to fully cure. When attempting to attach the mirror, the base came off the window. I was able to wipe the remaining liquid glue off the glass. The glue is just not curing. Don't buy this stuff!
    Date published: 2020-02-13
    Rated 1 out of 5 by from Doesn't work..... I bought this product at Advanced Auto Parts a couple weeks ago and just tried to put it on in 64 degree weather. Let the activator dry for 5 minutes and then put the adhesive on each side. Didn't think it was going to work after holding it on 2 full minutes. Wasn't even tacky. I think I wasted about $6 on this.
    Date published: 2019-11-16
    Rated 1 out of 5 by from PRODUCT DOES NOT ADHERE TO GLASS! I would give the product a zero rating if I could. I followed the instructions as carefully and thoroughly as any person possibly could. Although the instructions say ready to mount in 15 minutes I tried to play it safe and waited overnight. When I tried to mount the mirror it simply fell off. Barely a hint of adhesion to the glass. Unless this is an isolated bad batch I can only say that such an obviously worthless and misleading product should be taken off the market IMMEDIATELY! I am going to let my retailer (and everyone else) know that this is a bogus product that will leave only unhappy customers. I will request a refund from them as well so that maybe you will get some feedback from them (major chain.)
    Date published: 2019-10-04
    • y_2020, m_8, d_13, h_15
    • bvseo_bulk, prod_bvrr, vn_bulk_3.0.10
    • cp_1, bvpage1
    • co_hasreviews, tv_0, tr_3
    • loc_en_US, sid_B40066497|3m-country-catalog|FUZEexperience|en_US, prod, sort_[SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
    • clientName_3m-country-catalog
    • bvseo_sdk, java_sdk, bvseo-4.0.0
    • CLOUD, getContent, 49ms
    Product Support

    Specific product and application questions


    Message Us

    We welcome your questions and comments about 3M Products and only use the information you provide to respond to your message.

    All fields are required unless indicated optional.

    • The information you provide on this Contact Us form will be used to respond to your request and as further described in our  Internet Privacy Policy.

      Please be aware that this information (including the original and the subsequent reply) may be transferred to a server located in the U.S. for metrics and storage. If you do not consent to this use of your personal information, please do not use the Contact Us system.

    Follow Us
    The brands listed above are trademarks of 3M.
    Change Location
    United States - English